On average, I am asked about UFFI at least weekly. I give the same story every time: The item in question was used to insulate existing homes in an attempt to make poorly insulated homes better. This is the same reason that we find Vermiculite insulation in the attics. Below is an article from CMHC that explains it fully and what should be taken away from this is that unless the UFFI is getting wet, it should pose no more health risk than the carpets, cabinets, counters and flooring in the home.
What Is UFFI?
Urea-formaldehyde foam insulation (UFFI) was developed in Europe in the 1950s as an improved means of insulating difficult-to-reach cavities in house walls. It is typically made at a construction site from a mixture of urea-formaldehyde resin, a foaming agent and compressed air. When the mixture is injected into the wall, urea and formaldehyde unite and "cure" into an insulating foam plastic.
During the 1970s, when concerns about energy efficiency led to efforts to improve home insulation in Canada, UFFI became an important insulation product for existing houses. Most installations occurred between 1977 and its ban in Canada in 1980.
Why Was UFFI Banned?
In the insulating process, a slight excess of formaldehyde was often added to ensure complete "curing" with the urea to produce the urea-formaldehyde foam. That excess was given off during the curing, almost entirely within a day or two of injection. Properly installed, UFFI might not have resulted in any problem. Unfortunately, however, UFFI was sometimes improperly installed or used in locations where it should not have been. Enough complaints were received, particularly from people living in small, well-sealed homes, that Canadian authorities became concerned about possible health implications. The further use of UFFI was banned in 1980.
What Is Formaldehyde?
Formaldehyde is a pungent, colourless gas commonly used in water solution as a preservative and disinfectant. It is also a basis for major plastics, including durable adhesives. It occurs naturally in the human body and in the outdoor environment. Formaldehyde is used to bond plywood, particleboard, carpets and fabrics, and it contributes to "that new house smell." Formaldehyde is also a by product of combustion; it is found in tobacco smoke, vehicle exhaust and the fumes from furnaces, fireplaces and wood stoves.
While small amounts of formaldehyde are harmless, it is an irritating and toxic gas in significant concentrations. Symptoms of overexposure to formaldehyde include irritation to eyes, nose and throat; persistent cough and respiratory distress; skin irritation; nausea; headache; and dizziness.
Health Canada has determined that 0.1 parts per million (ppm) is a safe level of formaldehyde in the home. Sensitivity to this level may vary based on individual age and health.
Health effects.
Health effects of Urea-Formaldehyde are put into effect when the elevated level is reached. Urea-formaldehyde releases formaldehyde emissions into the air. This triggers watery eyes, nose irritations, wheezing and coughing, fatigue, skin rash, severe allergic reactions, burning sensations in the eyes and throat, nausea, and difficulty in breathing in some humans (usually 0.1 ppm). Studies have shown that exposure may cause cancer in humans and animals. Occupants of UFFI insulated homes experienced systemic symptoms such as headache, malaise, insomnia, anorexia, and loss of libido. Irritation of the mucus membrane (specifically eyes, nose, and throat) is a common upper respiratory tract symptom to be found in both home and work environments containing enough UFFI- insulation concentration. However when compared to control groups, the frequency of symptoms did not exceed the controls expect when it came to wheezing, difficult breathing, and a burning skin sensation. Controlled studies have suggested that tolerance to formaldehydes odor and irritating effects can occur over a prolonged exposure. Tolerance, sensitivity, and idiosyncratic reactions should be considered for further investigation. The effects of cancer or congenital malformations may be too low to assess.
Should You Be Concerned About UFFI Today?
Tests show that UFFI is not a source of over-exposure to formaldehyde after the initial curing and release of excess gas. As it was last installed in 1980, it would certainly not be causing excess indoor formaldehyde today. Houses with UFFI show no higher formaldehyde levels than those without it. However, if UFFI comes in contact with water or moisture, it could begin to break down. Wet or deteriorating UFFI should be removed by a specialist and the source of the moisture problem should be repaired.
In new or other well-sealed houses, significant indoor formaldehyde levels may still occur when new carpets or wood composite materials, such as plywood, particleboard and waferboard, are used in home construction, cabinetry and furnishings. These are the most likely sources of high formaldehyde levels in the home today.
If you are asked for a UFFI declaration.
Since 1993, a UFFI declaration has not been required for mortgage insurance under the National Housing Act. However, a UFFI declaration may still be requested as part of a real estate listing or an agreement of purchase and sale. Even though UFFI should not be a cause for concern, you may, depending on where you live in Canada, be asked to declare whether or not it is in your home.
Some home inspectors will have the training or experience to identify UFFI. You can make a physical check of the home yourself. Look for a series of small patched holes, 1.2 to 2 cm (1/2 to 3/4 in.) across, at regular intervals on exterior or interior walls. Foam may be obvious where floor joists meet the exterior walls of the basement or around electrical outlets or switch plates. These indicators do not necessarily mean that UFFI is present, but they may alert you to the possibility.
Darren St.Jacques is a certified master home inspector with Nook 'n' Cranny Home Inspections Inc. in Hamilton, Ontario. Nook 'n' Cranny Home Inspections Inc. also performs air quality sampling and testing for Asbestos, Radon, Allergens, Mold.
Source of information: CMHC and Wkipedia.
February 18, 2012
February 12, 2012
Licensing of home inspectors
Thanks to some media publications and the likes of a certain contractor-turned TV personality, home inspectors have been painted with the tainted brush of entertainment.
Are some home inspectors more experienced, qualified and trained than other's? Of course they are. Like any service or profession, there are good, bad and ugly stories to be told. It's human nature for us to hear about the bad and ugly ones, which typically only make up about 10% of the other good or great inspections people have had.
Which brings me to accountability: Who oversees the home inspectors? Who regulates the home inspection industry? Nobody?
The answer is not so simple: Here in Canada, the home inspection industry is largely unregulated, although one main association here in Ontario- *OAHI and other provincial arms under CAHPI, have been trying to position themselves as the regulating body for the home inspection industry for some time. They are recognized by CMHC and other government entities, so this may come to pass. There are other associations that inspectors belong to who are trying to be recognized, but cannot make headway into the mix to be considered as alternatives.
British Columbia and Alberta are the only 2 provinces to date to license its home inspectors. The closest accreditation to a licensed home inspector elsewhere is a Registered Home Inspector. Not to say that other inspectors are less qualified if they are not RHI's, because many are. It's just what is recognized by real estate offices, CMHC and Government and even that contractor turned TV personality that thinks he knows all about what a home inspector should have seen, thinks that you should choose a registered home inspector.
Rumour has it that Ontario has plans to license the home inspection industry, but when is any one's guess. I'm sure there are many things that need to be in place before this can happen. I for one, look forward to being a licensed home inspector, and I know that many of my fellow inspectors do as well. For those of us that are full time home inspectors, we welcome the opportunity to add credence to our trade and state that we are professionals.
For consumers; Licensing of home inspectors will provide a standard for home inspections that should reduce the "Ugly" stories to a minimum. The majority of bad and ugly inspection stories seem to be mostly caused by inexperienced, untrained or poorly educated home inspectors. As an RHI (Registered Home Inspector) will tell you: The requirements to become an RHI are tough and designed to elevate that person to a level that inspires confidence and professionalism.
For Inspectors; Becoming licensed means you have earned the right to be called a professional home inspector. Good or bad, you have at least met minimum requirements, other than an online exam taken through a home inspection association. The licensing of inspectors will thin the heard and reduce the chaff that causes the headaches- at least until they have finished their education and put in the effort to become a properly trained inspector. If you have put in your time for education, training, experience and so forth, you deserve to be considered for an inspection booking over the person without your investment of time and money- right?
In my opinion...
Darren St.Jacques
(soon to be an RHI)
*OAHI (Ontario Association of Home Inspectors) CAHPI (Canadian Association of Home and Property Inspectors)
Are some home inspectors more experienced, qualified and trained than other's? Of course they are. Like any service or profession, there are good, bad and ugly stories to be told. It's human nature for us to hear about the bad and ugly ones, which typically only make up about 10% of the other good or great inspections people have had.
Which brings me to accountability: Who oversees the home inspectors? Who regulates the home inspection industry? Nobody?
The answer is not so simple: Here in Canada, the home inspection industry is largely unregulated, although one main association here in Ontario- *OAHI and other provincial arms under CAHPI, have been trying to position themselves as the regulating body for the home inspection industry for some time. They are recognized by CMHC and other government entities, so this may come to pass. There are other associations that inspectors belong to who are trying to be recognized, but cannot make headway into the mix to be considered as alternatives.
British Columbia and Alberta are the only 2 provinces to date to license its home inspectors. The closest accreditation to a licensed home inspector elsewhere is a Registered Home Inspector. Not to say that other inspectors are less qualified if they are not RHI's, because many are. It's just what is recognized by real estate offices, CMHC and Government and even that contractor turned TV personality that thinks he knows all about what a home inspector should have seen, thinks that you should choose a registered home inspector.
Rumour has it that Ontario has plans to license the home inspection industry, but when is any one's guess. I'm sure there are many things that need to be in place before this can happen. I for one, look forward to being a licensed home inspector, and I know that many of my fellow inspectors do as well. For those of us that are full time home inspectors, we welcome the opportunity to add credence to our trade and state that we are professionals.
For consumers; Licensing of home inspectors will provide a standard for home inspections that should reduce the "Ugly" stories to a minimum. The majority of bad and ugly inspection stories seem to be mostly caused by inexperienced, untrained or poorly educated home inspectors. As an RHI (Registered Home Inspector) will tell you: The requirements to become an RHI are tough and designed to elevate that person to a level that inspires confidence and professionalism.
For Inspectors; Becoming licensed means you have earned the right to be called a professional home inspector. Good or bad, you have at least met minimum requirements, other than an online exam taken through a home inspection association. The licensing of inspectors will thin the heard and reduce the chaff that causes the headaches- at least until they have finished their education and put in the effort to become a properly trained inspector. If you have put in your time for education, training, experience and so forth, you deserve to be considered for an inspection booking over the person without your investment of time and money- right?
In my opinion...
Darren St.Jacques
(soon to be an RHI)
*OAHI (Ontario Association of Home Inspectors) CAHPI (Canadian Association of Home and Property Inspectors)
February 05, 2012
Asbestos in your home
Asbestos:
Asbestos is a natural mineral with unusual qualities. It is strong enough to resist high temperatures, chemical attack and wear. A poor conductor, it insulates well against heat and electricity.
What has asbestos been used for?
Asbestos has been used in hundreds of applications and products over the past 4,500 years. The ancient Greeks wove it into oil lamp wicks, funeral shrouds and ceremonial tablecloths. During the 1800s, it insulated the hot engines, boilers and piping that powered the Industrial Revolution.
For half a century, until the 1980s, asbestos was used in office buildings, public buildings and schools. It insulated hot water heating systems, and was put into walls and ceilings as insulation against fire and sound.
Asbestos has also been widely used in transportation and electrical appliances, frequently mixed with, and encased in, other materials.
Asbestos has also been found in many products around the house. It has been used in clapboard; shingles and felt for roofing; exterior siding; pipe and boiler covering; compounds and cement, such as caulk, putty, roof patching, furnace cement and driveway coating; wallboard; textured and latex paints; acoustical ceiling tiles and plaster; vinyl floor tiles; appliance wiring; hair dryers; irons and ironing board pads; flame-resistant aprons and electric blankets; and clay pottery. Loose-fill vermiculite insulation may contain traces of “amphibole” asbestos.
What health problems are associated with exposure to asbestos?
Health Canada states that the asbestos content of a product does not indicate its health risk.
Asbestos poses health risks only when fibres are in the air that people breathe. Asbestos fibres lodge in the lungs, causing scarring that can ultimately lead to severely impaired lung function (asbestosis) and cancers of the lungs or lung cavity.
When can asbestos be a problem in the home?
Today, far fewer products in the home contain asbestos. Current products that do contain the material are better made to withstand wear and use.
However, frequent or prolonged exposure to asbestos fibres may still bring health risks. This can happen with the release of fibres into the air when asbestos-containing products break down, either through deterioration as they age or when they are cut. People can put themselves at risk — often without realizing it — if they do not take proper precautions when repairs or renovations disturb asbestos containing materials. This can occur in a number of situations:
•Disturbing loose-fill vermiculite insulation which may contain asbestos
•Removing deteriorating roofing shingles and siding containing asbestos, or tampering with roofing felt that contains asbestos
•Ripping away old asbestos insulation from around a hot water tank
•Sanding or scraping vinyl asbestos floor tiles
•Breaking apart acoustical ceilings tiles containing asbestos
•Sanding plaster containing asbestos, or sanding or disturbing acoustical plaster that gives ceilings and walls a soft, textured look.
•Sanding or scraping older water-based asbestos coatings such as roofing compounds, spackling, sealants, paint, putty, caulking or drywall
•Sawing, drilling or smoothing rough edges of new or old asbestos materials
How to minimize the asbestos risks in the home?
* Nook 'n' Cranny Home Inspections recommends testing of suspected materials for asbestos in your home through an accredited testing laboratory.
Information courtesy of CMHC @ http://www.cmhc.ca/en/co/maho/yohoyohe/inaiqu/inaiqu_001.cfm
Asbestos is a natural mineral with unusual qualities. It is strong enough to resist high temperatures, chemical attack and wear. A poor conductor, it insulates well against heat and electricity.
What has asbestos been used for?
Asbestos has been used in hundreds of applications and products over the past 4,500 years. The ancient Greeks wove it into oil lamp wicks, funeral shrouds and ceremonial tablecloths. During the 1800s, it insulated the hot engines, boilers and piping that powered the Industrial Revolution.
For half a century, until the 1980s, asbestos was used in office buildings, public buildings and schools. It insulated hot water heating systems, and was put into walls and ceilings as insulation against fire and sound.
Asbestos has also been widely used in transportation and electrical appliances, frequently mixed with, and encased in, other materials.
Asbestos has also been found in many products around the house. It has been used in clapboard; shingles and felt for roofing; exterior siding; pipe and boiler covering; compounds and cement, such as caulk, putty, roof patching, furnace cement and driveway coating; wallboard; textured and latex paints; acoustical ceiling tiles and plaster; vinyl floor tiles; appliance wiring; hair dryers; irons and ironing board pads; flame-resistant aprons and electric blankets; and clay pottery. Loose-fill vermiculite insulation may contain traces of “amphibole” asbestos.
What health problems are associated with exposure to asbestos?
Health Canada states that the asbestos content of a product does not indicate its health risk.
Asbestos poses health risks only when fibres are in the air that people breathe. Asbestos fibres lodge in the lungs, causing scarring that can ultimately lead to severely impaired lung function (asbestosis) and cancers of the lungs or lung cavity.
When can asbestos be a problem in the home?
Today, far fewer products in the home contain asbestos. Current products that do contain the material are better made to withstand wear and use.
However, frequent or prolonged exposure to asbestos fibres may still bring health risks. This can happen with the release of fibres into the air when asbestos-containing products break down, either through deterioration as they age or when they are cut. People can put themselves at risk — often without realizing it — if they do not take proper precautions when repairs or renovations disturb asbestos containing materials. This can occur in a number of situations:
•Disturbing loose-fill vermiculite insulation which may contain asbestos
•Removing deteriorating roofing shingles and siding containing asbestos, or tampering with roofing felt that contains asbestos
•Ripping away old asbestos insulation from around a hot water tank
•Sanding or scraping vinyl asbestos floor tiles
•Breaking apart acoustical ceilings tiles containing asbestos
•Sanding plaster containing asbestos, or sanding or disturbing acoustical plaster that gives ceilings and walls a soft, textured look.
•Sanding or scraping older water-based asbestos coatings such as roofing compounds, spackling, sealants, paint, putty, caulking or drywall
•Sawing, drilling or smoothing rough edges of new or old asbestos materials
How to minimize the asbestos risks in the home?
- If you do not know if products in your home contain asbestos, have an experienced person inspect them. If there is asbestos, the best interim measure (unless the product is peeling or deteriorating) is to seal the surface temporarily so that fibres will not be released into indoor air. If the product is already protected or isolated, simply leave it alone.
- It is a complex and expensive matter to remove asbestos, and should be done by an experienced contractor. When disturbing an asbestos product, maximum precautions must be taken to safeguard the workers and anybody else who may be nearby. Asbestos dust must remain within the work area so that it cannot be breathed in by unprotected persons.
Information courtesy of CMHC @ http://www.cmhc.ca/en/co/maho/yohoyohe/inaiqu/inaiqu_001.cfm
January 20, 2012
Radon in granite counter tops?
Q. What about radon and radioactivity in granite counter tops?
Radon is produced from the natural decay of uranium found in rock. Granite used to produce commercial products, such as counter tops, can contain varying amounts of uranium. Some granites could contain more natural uranium than others, and thus possibly show higher than expected radiation or radon levels, however, in the vast majority of cases, these levels are not expected to be significant. Health Canada completed a study in February 2010 of 33 types of granite commonly purchased in Canada and none were found to have significant levels of radon.
At this time, Health Canada expects that the main source of radon in a house will be soil gas (containing radon formed by the decay of uranium found in rock under the house) which is drawn inside naturally by differences in pressure between the indoor environment and the outside. Our recommendation is that you reduce your radon risk by first testing the air in your house to determine the radon level.
Please feel free to leave comments, or share this with others.
Thanks for reading this article,
Darren
http://www.nookncranny.ca/
January 17, 2012
EMF's - Electro Magnetic Fields
EMF's, or Electro Magnetic Fields are all around us, but where you live and what equipment is nearby, can influence how much EMF is or could become, an issue. Can the electric and magnetic fields (EMF) to which people are routinely exposed cause health effects? What are sources of EMFs, and when are EMFs dangerous?
EMF (or ElectroMagnetic Field) is a broad term which includes electric fields generated by charged particles in motion, and radiated fields such as TV, radio, hair dryer, and microwaves. Electric fields are measured in units of volts per meter or V/m. Magnetic fields are measured in milli-Gauss or mG. The field is always strongest near the source and diminishes as you move away from the source. These energies have the ability to influence particles at great distances. For example, the radiation from a radio tower influences the atoms within a distant radio antenna, allowing it to pick up the signal. Despite the many wonderful conveniences of electrical technology, the effects of EMF on biological tissue remains the most controversial aspect of the EMF issue, with virtually all scientists agreeing that more research is necessary to determine safe or dangerous levels.
To read more of this article, please click the following link that will take you to a page in my website. CLICK TO READ MORE
Thanks for reading..
Darren
EMF (or ElectroMagnetic Field) is a broad term which includes electric fields generated by charged particles in motion, and radiated fields such as TV, radio, hair dryer, and microwaves. Electric fields are measured in units of volts per meter or V/m. Magnetic fields are measured in milli-Gauss or mG. The field is always strongest near the source and diminishes as you move away from the source. These energies have the ability to influence particles at great distances. For example, the radiation from a radio tower influences the atoms within a distant radio antenna, allowing it to pick up the signal. Despite the many wonderful conveniences of electrical technology, the effects of EMF on biological tissue remains the most controversial aspect of the EMF issue, with virtually all scientists agreeing that more research is necessary to determine safe or dangerous levels.
To read more of this article, please click the following link that will take you to a page in my website. CLICK TO READ MORE
Thanks for reading..
Darren
January 13, 2012
Snow is here! Are you ready?
Ah yes, the white stuff is here or has been in some areas for a while. Are you ready? Below is a checklist of things to get or do so you're not left 'in the cold' so to speak. In some respect, it's being prepared for the worst situations. Extreme weather can shut down utilities, stores, banks and so on. Having some spares such as food, water, gasoline, money (cash), and means of heating and cooking are recommended.
*De-icing salt for the walks and steps. Remember: You are legally responsible if somebody slips or falls on your property, like the mail or newspaper carriers.
*Have at least one snow shovel and consider buying a steel shovel for ice and packed snow.
*If you have put off installing snow/ice tires on your vehicles: Get them on now. They are proven to stop you in shorter distances and provide traction to get through snow.
*PLEASE SLOW DOWN! You gain only seconds by driving quickly, but could possibly waste a lifetime (yours or someone else's) by being in an accident!
*Have some emergency supplies in your car, such as a collapsible shovel, blankets, spare gloves, mitts and hats, bottled water, chocolate or cereal bars.
*Buy one of those emergency kits for the vehicles.
*If power outages are common in your area, consider getting a gas generator. Make sure to keep a full gas can in the shed. They are easy to operate and could keep you warm by providing electricity for heaters and to heat food and water for days!
*Most home phones will only work with household power, so if you don't have one- buy a basic cellphone. These can also be bought used for a few bucks!
*Remember your pets, they suffer in the cold as well.
*Have ready to eat foods and bottled water on hand, including powdered milk.
*Have your furnace serviced if its been over 3 years since the last time.
These are just a few suggestions to help guide you in the right direction but I'm sure you get the idea.
Stay safe and warm!
Darren
*De-icing salt for the walks and steps. Remember: You are legally responsible if somebody slips or falls on your property, like the mail or newspaper carriers.
*Have at least one snow shovel and consider buying a steel shovel for ice and packed snow.
*If you have put off installing snow/ice tires on your vehicles: Get them on now. They are proven to stop you in shorter distances and provide traction to get through snow.
*PLEASE SLOW DOWN! You gain only seconds by driving quickly, but could possibly waste a lifetime (yours or someone else's) by being in an accident!
*Have some emergency supplies in your car, such as a collapsible shovel, blankets, spare gloves, mitts and hats, bottled water, chocolate or cereal bars.
*Buy one of those emergency kits for the vehicles.
*If power outages are common in your area, consider getting a gas generator. Make sure to keep a full gas can in the shed. They are easy to operate and could keep you warm by providing electricity for heaters and to heat food and water for days!
*Most home phones will only work with household power, so if you don't have one- buy a basic cellphone. These can also be bought used for a few bucks!
*Remember your pets, they suffer in the cold as well.
*Have ready to eat foods and bottled water on hand, including powdered milk.
*Have your furnace serviced if its been over 3 years since the last time.
These are just a few suggestions to help guide you in the right direction but I'm sure you get the idea.
Stay safe and warm!
Darren
January 12, 2012
Energy efficiency for homes
Saving energy should be a goal for all home owners, businesses and governments. Not only to save money, but to reduce the ongoing damage to our planet in some way. This doesn't always mean an expensive retrofit of the home, or replacement of major equipment and appliances. Although newer energy star rated items, such as furnaces, AC's, refrigeration and cooking equipment are far more energy efficient today, than most over 10 years and worth considering for replacement in the near future.
One very useful publication I really like is "Keeping the heat in", provided by the Office of Energy Efficiency- Natural Resources Canada. Below is a link to their website, where you can read the book.
One very useful publication I really like is "Keeping the heat in", provided by the Office of Energy Efficiency- Natural Resources Canada. Below is a link to their website, where you can read the book.
January 11, 2012
Radon. Why aren't we more concerned about it?
For many years, we have been conscious of the very real and unhealthy effects of Radon. (The 2nd leading cause of lung cancer behind cigarette smoking) Through professional inspection, testing, building practices, public awareness programs and the support of the many real estate associations, steps could be taken to educate the public and mitigate the issue for the health and safety of millions of home owners in Canada. For some reason, this very real health concern doesn't seem to be much concern or mentioned very much. Does it mean Canada doesn't have Radon? Nope, that's not it, as we do. According to many publications, it would appear that Canada has radon, and depending where you test, readings could be higher than that from only down the road.
So why don't we hear very much about it? What can be done about it? Well, apparently there is already a being being tabled in front of the government to possibly make pre-listing inspection and testing a requirement of selling a home, with the results and any repairs made available to prospective buyers. As of right now, home buyers can request a test of a home being sold is carried out, or present home sellers could be proactive and have the home tested and provide the test results to future buyers.
For more information and solutions from CMHC and Health Canada, Please click the following links.
CMHC on Radon.
Health Canada on Radon.
So why don't we hear very much about it? What can be done about it? Well, apparently there is already a being being tabled in front of the government to possibly make pre-listing inspection and testing a requirement of selling a home, with the results and any repairs made available to prospective buyers. As of right now, home buyers can request a test of a home being sold is carried out, or present home sellers could be proactive and have the home tested and provide the test results to future buyers.
For more information and solutions from CMHC and Health Canada, Please click the following links.
CMHC on Radon.
Health Canada on Radon.
May 25, 2011
Ten Tips to Speed up Your Home Inspection
Home sellers can speed their home inspection by following these suggestions. The inspection will go smoother, with fewer concerns to delay closing. If access to items normally inspected is not possible, it creates a sense of unknown and could cause concern for the buyer, whom is normally already nervous about what might be found.
1. Confirm that water, electric and gas service are on, with gas pilot lights burning.
2. Ensure pets won't hinder the inspection. Ideally, they should be removed from premises or secured outside. Tell your agent about any pets at home.
3. Replace burned out bulbs to avoid a "Light is inoperable" report that may suggest an electrical problem.
4. Test smoke and carbon monoxide detectors, and replace dead batteries.
5. Clean or replace dirty HVAC (Heating Ventilation Air Conditioning) air filters. They should fit securely.
6. Remove stored items, debris and wood from foundation. These may be cited as "conditions conducive" for termites.
7. Remove items blocking access to HVAC equipment, electric service panels, water heaters, attics and crawl spaces.
8. Unlock areas the inspector must access - attic doors or hatches, electric service panels, closets, fence gates and crawl spaces.
9. Trim tree limbs to 10' from the roof and shrubs from the house to allow access.
10. Attend to broken or missing items like doorknobs, locks and latches; windowpanes, screens and locks; gutters, downspouts and chimney caps.
Checking these areas before your home inspection is an investment in selling your property. Your real estate agent will thank you!
Darren
1. Confirm that water, electric and gas service are on, with gas pilot lights burning.
2. Ensure pets won't hinder the inspection. Ideally, they should be removed from premises or secured outside. Tell your agent about any pets at home.
3. Replace burned out bulbs to avoid a "Light is inoperable" report that may suggest an electrical problem.
4. Test smoke and carbon monoxide detectors, and replace dead batteries.
5. Clean or replace dirty HVAC (Heating Ventilation Air Conditioning) air filters. They should fit securely.
6. Remove stored items, debris and wood from foundation. These may be cited as "conditions conducive" for termites.
7. Remove items blocking access to HVAC equipment, electric service panels, water heaters, attics and crawl spaces.
8. Unlock areas the inspector must access - attic doors or hatches, electric service panels, closets, fence gates and crawl spaces.
9. Trim tree limbs to 10' from the roof and shrubs from the house to allow access.
10. Attend to broken or missing items like doorknobs, locks and latches; windowpanes, screens and locks; gutters, downspouts and chimney caps.
Checking these areas before your home inspection is an investment in selling your property. Your real estate agent will thank you!
Darren
May 21, 2011
No moisture meter? Really??
I got a call yesterday from a sales agent that has referred me previously, asking me if I could help her out with something.
It seems that clients of hers used a home inspector they found and during the inspection, he saw some stains under a couple of windows and declared they were wet.
The agent asked him if he had a moisture meter to test them, but he didn't have one.... Really?
A home inspector without a moisture meter is like a piece of bread with nothing on it... quite useless!
I tested the areas he noted first with my infrared camera, then with a moisture meter. Nada. The areas were as dry as an interior wall- 6-7% moisture.
A person that calls themselves a home inspector should have the basic tools of the job and properly back up all suspicions with testing. This one needs more training and should invest in some proper tools before they really mess up a deal and give out poor information.
It seems that clients of hers used a home inspector they found and during the inspection, he saw some stains under a couple of windows and declared they were wet.
The agent asked him if he had a moisture meter to test them, but he didn't have one.... Really?
A home inspector without a moisture meter is like a piece of bread with nothing on it... quite useless!
I tested the areas he noted first with my infrared camera, then with a moisture meter. Nada. The areas were as dry as an interior wall- 6-7% moisture.
A person that calls themselves a home inspector should have the basic tools of the job and properly back up all suspicions with testing. This one needs more training and should invest in some proper tools before they really mess up a deal and give out poor information.
May 18, 2011
Good, Bad & Ugly
During most home inspections, I find typical issues such as maintenance items or general improvement suggestions. But on occasion, I find some concerns that clients don't want to deal with, or just can't afford to. These types of concerns could be structural issues, moisture penetration in the basement or electrical items.
One such inspection comes to mind; I recently did an inspection on a home with a crawl space that was wet. It also did not have a proper foundation, but had a wood skirt around the exterior made of different materials, nearly all was rotting! The house was being supported by concrete blocks sitting on bare ground under the floor joists. Bare wet earth will cause the floor and framing system to rot over time, as the moisture will evaporate upwards into the building. There was some bowing of an exterior wall that was worrisome but this was just another of many issues with the house, much to the relief of her trying so hard to be supportive dad, my client walked away from the deal.
Incredibly though her sales agent seemed to be upset with me for delivering the news and was, in my opinion, quite rude and confrontational. At the end of the day, I sleep sound knowing I do my job as honestly and thoroughly as I can.
Home inspectors are trying to help people with what is usually the most expensive and long-term purchase of someones life. We need to be conscious of the ramifications of not doing this to the best of our abilities. A smart person once said "If in doubt, Bow out". Good advice in my opinion.
One such inspection comes to mind; I recently did an inspection on a home with a crawl space that was wet. It also did not have a proper foundation, but had a wood skirt around the exterior made of different materials, nearly all was rotting! The house was being supported by concrete blocks sitting on bare ground under the floor joists. Bare wet earth will cause the floor and framing system to rot over time, as the moisture will evaporate upwards into the building. There was some bowing of an exterior wall that was worrisome but this was just another of many issues with the house, much to the relief of her trying so hard to be supportive dad, my client walked away from the deal.
Incredibly though her sales agent seemed to be upset with me for delivering the news and was, in my opinion, quite rude and confrontational. At the end of the day, I sleep sound knowing I do my job as honestly and thoroughly as I can.
Home inspectors are trying to help people with what is usually the most expensive and long-term purchase of someones life. We need to be conscious of the ramifications of not doing this to the best of our abilities. A smart person once said "If in doubt, Bow out". Good advice in my opinion.
April 29, 2011
Home Inspections for the home seller.
Pre-Listing / Home Seller House Inspections
It is typical that a potential home buyer will conduct a home inspection on your house prior to the final signing of the agreement. And sometimes the home inspection can reveal issues that jeapordize the deal, very often because of a bunch of minor repairs that could have been remedied before you listed the house. It is also possible that a larger, more serious issue is present that you may not be aware of and could be fixed right away.
You may as well know what their inspector may find, by getting your home inspected before you list it, or even just after you list your home.
Having a home inspection performed ahead of time can help you in many ways:
It is typical that a potential home buyer will conduct a home inspection on your house prior to the final signing of the agreement. And sometimes the home inspection can reveal issues that jeapordize the deal, very often because of a bunch of minor repairs that could have been remedied before you listed the house. It is also possible that a larger, more serious issue is present that you may not be aware of and could be fixed right away.
You may as well know what their inspector may find, by getting your home inspected before you list it, or even just after you list your home.
Having a home inspection performed ahead of time can help you in many ways:
- Relief of buyers suspicions and concerns.
- Will help with pricing the home.
- Repairs can be done ahead of time.
- Avoid negotiating over defects.
- Encourages buyer to waive their own home inspection condition.
- It may alert you to items of immediate personal concern.
- Allows you to see your home through the eyes of a critical third-party.
- Reduces liability by adding supporting documentation to your disclosure information.
- Alerts you to immediate safety issues before agents and visitors tour your home.
- Studies show pre-inspected homes can sell twice as fast!
- Copies of the report along with receipts for repairs can be made available to potential buyers.
- The inspection process is as thorough and detailed as our Pre-Purchase inspection.
- You can also choose to upgrade their inspection to include an infrared thermal imaging scan.
April 26, 2011
Hamilton home inspections
A recent inspection shows why wood burning stoves and fireplaces should be checked and cleaned annually.
When I opened the damper to look up the flue, three dead birds fell out. Not nice, but more importantly, it indicates that the screen at the top is compromised and could easily allow birds to build a nest, blocking the flue. Which of course could cause smoke to billow back into the house.
April 16, 2011
Vermiculite insultation
There have been many ads running lately on television and radio regarding Vermiculite insulation and the health concern that it may contain a type of asbestos. Some people say remove it, others say leave it. It's difficult to know the right thing to do and unfortunately, your home inspector is not allowed to answer this question for you either.
The best thing you can do is educate yourself on the matter. If you or your home inspector does find vermiculite insulation, you have some options. The first and most important option is to have it tested to see if it does contain asbestos. If it's your own home, send a sample to a registered lab. If it's a house you are buying and the inspector finds it, then you could ask the home owner to have it tested, or ask permission to take a sample for testing. Not all vermiculite does contain asbestos, so it may be a worthwhile exercise.
The next option you have is whether you want to have it removed, or live with it. There are pros and cons in each case and you should weigh your individual situation out carefully. Think about the potential issues you may have with re-sale for instance, or if you have a young or soon to be born family... these are important considerations. You might be OK with it, but I have had clients that walked away from the house after it was found- they just didn't want to have anything to do with it, even if the seller offered to have it professionally removed and replaced with new insulation.
Anyway, I have included some links on my website: http://www.nookncranny.ca under asbestos in the homeowner information tab, that will lead you to two reputable publications regarding the potential health concerns and what steps can be taken.
As always, please don't hesitate to contact me or post a comment if you have time.
Darren
 |
| Vermiculite insulation found during a recent home inspection. |
There have been many ads running lately on television and radio regarding Vermiculite insulation and the health concern that it may contain a type of asbestos. Some people say remove it, others say leave it. It's difficult to know the right thing to do and unfortunately, your home inspector is not allowed to answer this question for you either.
The best thing you can do is educate yourself on the matter. If you or your home inspector does find vermiculite insulation, you have some options. The first and most important option is to have it tested to see if it does contain asbestos. If it's your own home, send a sample to a registered lab. If it's a house you are buying and the inspector finds it, then you could ask the home owner to have it tested, or ask permission to take a sample for testing. Not all vermiculite does contain asbestos, so it may be a worthwhile exercise.
The next option you have is whether you want to have it removed, or live with it. There are pros and cons in each case and you should weigh your individual situation out carefully. Think about the potential issues you may have with re-sale for instance, or if you have a young or soon to be born family... these are important considerations. You might be OK with it, but I have had clients that walked away from the house after it was found- they just didn't want to have anything to do with it, even if the seller offered to have it professionally removed and replaced with new insulation.
Anyway, I have included some links on my website: http://www.nookncranny.ca under asbestos in the homeowner information tab, that will lead you to two reputable publications regarding the potential health concerns and what steps can be taken.
As always, please don't hesitate to contact me or post a comment if you have time.
Darren
March 15, 2011
Hamilton home inspections. When you gotta go...
Every now and then on a home inspection, I come across something strange or just not right.
This is a picture I took of a garage that was transformed into a "man cave" and had a urinal installed on the wall.
Of course, this is not allowed and doesn't meet any plumbing codes I'm aware of. The urinal was 'plumbed' to the exterior through a pipe beside the garage wall. My client wasn't too impressed by this and was going to ask for it to be removed. However, he ended up walking away from the house, due to some serious issues with the foundation walls that were bowing in and would cost more than he wanted to pay for repairs.
: D
Of course, this is not allowed and doesn't meet any plumbing codes I'm aware of. The urinal was 'plumbed' to the exterior through a pipe beside the garage wall. My client wasn't too impressed by this and was going to ask for it to be removed. However, he ended up walking away from the house, due to some serious issues with the foundation walls that were bowing in and would cost more than he wanted to pay for repairs.
: D
Subscribe to:
Posts (Atom)